1.What is the purpose of Inverse ARP?
A. to map a known IP address to a MAC address
B. to map a known DLCI to a MAC address
C. to map a known MAC address to an IP address
D. to map a known DLCI to an IP address
E. to map a known IP address to a SPID
F. to map a known SPID to a MAC address

2.RouterA is unable to reach RouterB. Both routers are running IOS version 12.0.
After reviewing the command output and graphic, what is the most likely cause of the problem?
A. incorrect bandwidth configuration
B. incorrect LMI configuration
C. incorrect map statement
D. incorrect IP address

3.At which layer of the OSI model does PPP perform?
A. Layer 2
B. Layer 3
C. Layer 4
D. Layer 5

4.Which protocol is an open standard protocol framework that is commonly used in VPNs, to provide secure end-to-end communications?
A. RSA
B. L2TP
C. IPsec
D. PPTP

5.What are the three things that the Netflow uses to consider the traffic to be in a same flow?
(Choose three)
A. IP address
B. Interface name
C. Port numbers
D. L3 protocol type
E. MAC address

6.Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch? (Choose two.)
A. SW1#show port-secure interface FastEthernet 0/12
B. SW1#show switchport port-secure interface FastEthernet 0/12
C. SW1#show running-config
D. SW1#show port-security interface FastEthernet 0/12
E. SW1#show switchport port-security interface FastEthernet 0/12

7.A network administrator is configuring ACLs on a Cisco router, to allow traffic from hosts on networks 192.168.146.0, 192.168.147.0, 192.168.148.0, and 192.168.149.0 only. Which two ACL statements, when combined, would you use to accomplish this task? (Choose two.)
A. access-list 10 permit ip 192.168.146.0 0.0.1.255
B. access-list 10 permit ip 192.168.147.0 0.0.255.255
C. access-list 10 permit ip 192.168.148.0 0.0.1.255
D. access-list 10 permit ip 192.168.149.0 0.0.255.255
E. access-list 10 permit ip 192.168.146.0 0.0.0.255
F. access-list 10 permit ip 192.168.146.0 255.255.255.0

8.A network administrator cannot establish a Telnet session with the indicated router. What is the cause of this failure?
A. A Level 5 password is not set.
B. An ACL is blocking Telnet access.
C. The vty password is missing.
D. The console password is missing.

9.Which Cisco Catalyst feature automatically disables the port in an operational PortFast upon receipt of a BPDU?
A. BackboneFast
B. UplinkFast
C. Root Guard
D. BPDU Guard
E. BPDU Filter

10.What are the alert messages generated by SNMP agents called?
A. TRAP
B. INFORM
C. GET
D. SET

11.What are the Popular destinations for syslog messages to be saved? (Choose three)
A. Flash
B. The logging buffer .RAM
C. The console terminal
D. Other terminals
E. Syslog server

12.What authentication type is used by SNMPv2?
A. HMAC-MD5
B. HMAC-SHA
C. CBC-DES
D. community strings

13.Which two statements about static NAT translations are true? (Choose two.)
A. They allow connections to be initiated from the outside.
B. They require no inside or outside interface markings because addresses are statically defined.
C. They are always present in the NAT table.
D. They can be configured with access lists, to allow two or more connections to be initiated from the outside.

14.When a DHCP server is configured, which two IP addresses should never be assignable to hosts?
(Choose two.)
A. network or subnetwork IP address
B. broadcast address on the network
C. IP address leased to the LAN
D. IP address used by the interfaces
E. manually assigned address to the clients
F. designated IP address to the DHCP server

15.Which two tasks does the Dynamic Host Configuration Protocol perform? (Choose two.)
A. Set the IP gateway to be used by the network.
B. Perform host discovery used DHCPDISCOVER message.
C. Configure IP address parameters from DHCP server to a host.
D. Provide an easy management of layer 3 devices.
E. Monitor IP performance using the DHCP server.
F. Assign and renew IP address from the default pool.

Important  Instructions

While submitting answers below in the " Message " Section MAKE SURE you type Question Number and Answer (For Example : 1. A , 2. B , 3.C ) and also mention the part number(For example: part 1, or part 2, or part 3 ) of the questions you are answering.

We will mail you your result in 10 seconds. " Mention Course Name as subject "

Your Name (required)

Your Email (required)

Your Number (required)

Subject

Your Message